HOME › Blogs › Planning large LED screens for aquarium exhibits

Planning large LED screens for aquarium exhibits

On a four-sided digital aquarium, fine-pitch COB Pro or COB Beta can carry an underwater scene around the entire exhibit. Transparent LED Film puts the fish on glass and keeps the gallery visible. Choose the effect from the position where guests will stand.

A turtle and tropical fish above a sunlit coral reef on two outer faces of a COB Pro exhibit
COB ProThe blue water and coral reef fill both faces around the corner.
The turtle and fish appear on transparent glass, with the gallery floor visible behind them
LED FilmThe gallery floor and back wall show through the glass between the fish.

Concept renderings of the same four-sided exhibit, viewed from the same position.

A four-sided digital aquarium or an inward-facing exhibit?

Four outward-facing sides. Start with the two long faces and two short ends of a rectangular island. Mark where guests approach, stop to read and turn the corner. Keep species names within a single face; let fish and background scenery cross the joins. The top and base can be plain architectural finishes.

Choose the cabinet grid for both face widths. For visitors reading a species name alongside footage, lay out the active area in whole cabinets. A COB Pro wall uses 600 × 337.5 mm cabinets. Equal numbers of columns and rows give a 16:9 picture. If a shorter face is nearly square or closer to 4:3, also try the 640 × 480 mm cabinets of COB Beta. At the same pitch the two give the same pixel spacing. The cabinet shape determines how well each fits the two widths at one common height. Choose one grid for the island and confirm its outside-corner detail with the supplier.

Inward-facing L-shaped walls. If visitors enter a room or follow a passage, turn the picture toward them. A pair of walls can share one reef scene across an inside corner. Mark the entrance and the main viewing position so the animator knows which wall guests see first.

Finished L-shaped COB Pro digital aquarium
Concept rendering. Two COB Pro walls meet at an inside corner. The reef continues onto the return wall, so visitors can follow the school of fish as they walk past.

Curved passage or overhead display. A flexible LED display follows a frame made to the curve. Mark where guests first see the wall, where they pass closest and where the video crosses a joint. A column or sphere viewed from several sides needs a wraparound content map. For a ceiling, reserve space for the support, retention and access system before fixing the screen outline.

Plan views of a cabinet wall, a curved LED frame and a transparent layer on the dry side of a window
Plan views. The arrows show where visitors stand. The pale blue area sits behind the glass. Keep the cable exit and power enclosure accessible on the dry side.

Existing window or empty tank. Decide what guests need to see through the glass when the video plays. A transparent LED Film aquarium can show moving fish while guests see through the glass. An opaque screen behind an empty viewing aperture can instead fill the whole opening with a continuous underwater scene. An old tank visible from two rooms may need two outward-facing displays if both audiences need to read labels.

A commercial LCD can suit a single rectangular viewing window that matches an available panel size. Projection is worth comparing in a dark space with a clear light path. At OdySea Aquarium, for example, the lobby uses projection while the café uses direct-view LED. Christie’s OdySea project.

What resolution fits your available wall space?

A 3.60 × 2.025 m COB Pro wall can show native 4K UHD at P0.9375, or native Full HD at P1.875. Both use six cabinets across and six high. The finer pitch gives the content designer twice as many pixels across each fish and four times as many pixels over the whole wall.

Four columns and four rows of COB Pro P1.25 cabinets form a 1920 by 1080 pixel display
One P1.25 cabinet has 480 × 270 pixels. Four across and four high give 1920 × 1080 pixels on a 2.40 × 1.35 m active face.
COB Pro native resolution by active wall size
Active width × height Cabinets
across × high
P0.9375
pixels
P1.25
pixels
P1.875
pixels
1.80 × 1.0125 m 3 × 3 1920 × 1080 1440 × 810 960 × 540
2.40 × 1.35 m 4 × 4 2560 × 1440 1920 × 1080 1280 × 720
3.60 × 2.025 m 6 × 6 3840 × 2160 2880 × 1620 1920 × 1080
4.80 × 2.70 m 8 × 8 5120 × 2880 3840 × 2160 2560 × 1440

How many pixels go around all four sides?

Take a COB Pro P1.25 island with 3.60 m long faces, 2.40 m ends and a common active height of 2.025 m. Each long face uses six cabinets across; each end uses four. All four are six cabinets high. Starting on a long face, unfold the perimeter in walking order:

Clockwise perimeter: A and C are 2880 pixels wide; B and D are 1920 pixels wide; all four faces are 1620 pixels high
One P1.25 example: 2880 + 1920 + 2880 + 1920 = 9600 × 1620 pixels across the four faces. These are nominal active areas. Use the approved corner drawing and processor map for the final export template.

The long face alone shows 2880 × 1620 pixels. The 9600-pixel width belongs to the whole loop. Ask the integrator to verify player decoding, output widths and processor capacity at the show frame rate before commissioning a single panorama file. An alternative is to split the master into synchronized outputs.

Square opening. Three COB Beta cabinets across and four high make a 1.92 × 1.92 m square. That square has 1536 × 1536 pixels at P1.25, 1248 × 1248 at P1.538, or 1032 × 1032 at P1.86. Give the animator the square canvas size before editing. A widescreen ocean clip will need a crop or borders to preserve the shape of the fish.

Curved wall. Measure the length along the display face. A tape stretched straight between the ends measures the chord and understates the width of the video canvas. Once the module grid is set, multiply the number of columns by each module’s horizontal pixels, and the number of rows by its vertical pixels. Mark the first column and the visitor’s approach on the drawing sent to the content team.

What does pixel pitch look like from the visitor’s position?

Follow the yellow stripe along a fish’s flank and the diagonal edge of its tail. Each sample below represents the same 60 × 60 mm patch of screen. That patch holds 64 pixels across at P0.9375, 48 at P1.25 and 32 at P1.875. The white box marks the part of the source photograph used in all three samples.

Pixel pitch simulation from one goatfish photograph with equal-size crops sampled at 64, 48 and 32 pixels across
Simulation · equal-area crops, enlarged. All three use the same photograph and sampling method. The comparison shows spatial detail. Screen brightness, black level, glass reflections and viewing distance must be judged on site. Source photograph by Dwayne Meadows, NOAA.

For a sample review, bring one fast-moving fish clip, a dark blue gradient and the smallest text visitors will read. Watch from the closest stopping point, then from across the passage. At each position check whether the eye and tail remain distinct and the letters stay legible. Then switch to the venue’s evening brightness preset and look for bands in the gradient and reflections in the viewing window.

How do you install and service a four-sided LED aquarium?

Have the structural team set out the base, support and anchoring for the freestanding frame. Mark faces A, B, C and D clockwise on the plan. Identify where power and data enter the island, where heat can escape and which opening gives a technician access after all four sides are closed.

Partly clad rectangular aquarium island showing its central frame and cabinet backs
Concept rendering. The openings show the space behind the LED faces. Before fitting the last cabinets, demonstrate how the power supply and receiving card can be reached once the trim is in place.

Setting the four outside corners

Request a sample outside-corner pair in the proposed cabinet finish. Check the visible joint from straight ahead and from the route around the island. Agree how the exposed edge will be protected, how trim affects the image, and whether a corner module can be removed without disturbing the next face. Record those decisions on the shop drawing.

Set one level line around the base. Dry-fit a bottom row around the perimeter and check the final D-to-A joint before stacking upward; a small alignment error can accumulate over four turns. Commission with a face ID and an upright arrow on each side, then run a horizontal stripe and a moving fish around the entire loop.

Illuminated grid wrapping around the projecting outside corner of a digital aquarium island
Concept rendering. Follow one grid row across the projecting edge to check the two faces are level. A moving clip also reveals a reversed face or a jump in the image at the join.

Site checks for exhibit walls and passages

  1. Survey the finished opening. Measure width and height at several points. Mark the visitor side, service route, glass edges, cable entry, power isolation and locations reached by cleaning spray. For a curve, record the arc length and radius, or the chord and the rise at its midpoint. Identify the inside and outside faces.
  2. Lay out the support and first row. On a flat wall the installer sets a level datum, aligns the supporting rails and checks the first cabinet row before building upward. On a curved wall the frame establishes the shape. Check the module layout across the tightest part of the curve. Have the structural team specify the support and retention for overhead sections.
  3. Prove the maintenance path. Before closing the surround, isolate the equipment and have a technician demonstrate how a module, power supply and receiving card can each be reached. Leave room for the extraction tool and connectors. Front-service cabinets still need a route to the building supply, isolation point and ventilation path.
  4. Commission with the glass and lighting in place. Run a numbered grid to reveal swapped cabinets, then move a fish slowly across a joint. Check the view from both ends of the corridor. Set the operating brightness with the venue team and save the signed-off configuration. For an exhibit next to live animals, agree the operating schedule with the aquarists.

Alternative layout: joining two inward-facing COB Pro walls

Set the bottom edges of both walls to one level line. Dry-fit the corner pair and the next cabinet on each side before filling the rows. Check the horizontal joints across the return and use a straightedge on each face to find a proud cabinet. Adjust the support until adjacent faces sit flush. The corner drawing should identify the two mating edges and show how each front module will come out after the trim is fitted.

COB Pro cabinet installation at a digital aquarium corner
Concept rendering. The open section shows the mounting grid behind the display. Check the first row and the return together while both faces are accessible.

Specify the 90° inside corner when ordering the cabinets. In DOIT VISION’s New Jersey showroom, the two cabinet edges were machined at 45° to form the turn. Have the supplier show the proposed edge profile and module removal path on the shop drawing before the frame is fabricated.

Cutaway from above showing two mitred cabinet edges meeting above the vertical LED seam
Concept rendering. Viewed from above, the two angled ends meet directly behind the vertical seam. This illustrates the joint geometry; the cabinet profile and fixings follow the project drawing.

With both faces powered, send a horizontal line across the join. First check that the rows meet at the same height. Then move a fish slowly across the corner and watch its outline from the main visitor position. If a column of the image repeats or disappears at the turn, check the edge coordinates in the processor map. The required offset depends on the built corner.

Alignment test at a 90-degree COB Pro cabinet joint
Concept rendering. A horizontal test line makes a height mismatch at the inside joint easy to spot. Use a moving clip to check the content map after the faces are aligned.
Adjustable mounting framework used for the New Jersey immersive COB showroom
DOIT VISION’s New Jersey showroom installation used an adjustable frame to align the two faces of a corner before setting the video map. View the showroom project.
Flexible LED module and cabinet assembly options for a shaped frame
For a curved passage, agree who supplies the shaped frame and where a technician can remove a module once the architectural trim is in place.

At SeaWorld San Diego’s jellyfish exhibit, the visible circular windows determined where standard panels could end and custom modules had to begin. Give the screen designer a dimensioned drawing of each window’s clear opening before the module layout is fixed. digiLED and AVI-SPL’s installation.

How does a four-sided transparent LED Film aquarium look?

For a see-through digital aquarium, use four supported glass panes and bond transparent LED Film to the dry interior face of each one. A fish lights up on the glass while the gallery stays visible between the fish. From some angles visitors can see the opposite pane as well. Leave space between schools in the animation so the two layers are easy to follow. See a daylight gallery concept rendering.

At a 90° corner, end each film sheet on its own pane. Mark the last active pixel on each side of the glass joint and show the cable exit on the pane drawing. A removable cover at the base is one way to keep the edge connections reachable. Test a fish crossing the join from the visitor’s side before finalizing the animation.

Two LED Film sheets ending on adjacent panes with a cable entering the base at the glass corner
Concept rendering. Each pane has its own film and bottom edge housing. The visible glass joint and the proposed cable route can be reviewed together on a corner sample.
Three stages of positioning adhesive LED Film on glass and powering the installed panel
Choose the film orientation and cable exit before placing the first sheet. Keep the edge connections accessible after the trim goes on.
Three amber fish shown against a dark gallery wall on the left and a bright wall on the right
Concept rendering. The dark wall on the left gives the amber fins a clearer outline. Against the brighter wall on the right, the fine strokes blend into the background. Judge contrast with a film sample and the venue’s own lighting.

For an existing water-retaining window, ask the venue, glazing supplier and integrator to confirm the dry mounting side, glass or acrylic type, coating and cleaning method. For a large permanent installation or a window facing daylight, also assess Holographic LED. Check captions from each visitor position, including through the opposite face.

Holographic LED content demo. Watch the fish cross the illuminated area while the room remains visible through the display. The overhead enclosure and feed cable show where the installation needs space.

Who sets up the screen, and who runs it each day?

Show playlist in the media player feeds the LED processor and its saved canvas map, then the LED wall
The integrator sets the wall map during commissioning. Staff normally work in the player’s playlist. A combined unit can perform both roles.

One reef or four different exhibits? For a continuous swim, use the saved A–B–C–D map and check the last edge of D against the first edge of A. For separate exhibits, give each face its own correctly sized clip or playlist zone. Keep the face IDs in the filenames so staff can change a species label on the intended side.

At handover, ask the integrator for the native canvas size, an example export, the approved frame rate and file format, the cabinet map, a backup of the processor settings and the name of the working playlist. Have staff rehearse a file change and a restart. For several synchronized walls, label which player feeds each surface and who maintains the show cues.

Pixel offset mapping used to carry a single image across the New Jersey showroom corner
The saved map assigns content pixels to each face at the showroom corner. Subsequent videos can reuse that map when they follow the same canvas template.

Replacing the morning loop

  1. Export a new version. Duplicate the approved project file, preserve its canvas size and frame rate, and export under a new filename. Keep the last working clip in the player library.
  2. Load and preview. Import the file into the player or media computer through the handover workflow. Duplicate the current playlist and replace the old clip in the copy. Preview the beginning, the final frame, the loop transition and any captions.
  3. Check it on the wall before opening. Call the normal exhibit brightness preset. Stand at the nearest visitor position, follow a fish across the seam and confirm text reads in the intended direction. Check the audio cue on synchronized shows.
  4. Put the new playlist on air. Select it for the correct screen or scheduled slot, verify one full loop and retain the previous playlist for rollback. If the new video looks stretched, compare its export size with the saved template before changing the processor map.

For a simple loop, the operator needs access to the designated player. For a show triggered by a sensor or synchronized with audio and lighting, the integrator should test the cue sequence and recovery after loss of power. Specify scheduling, remote access and synchronization when selecting the player and control equipment.

What should be included in an aquarium display quote?

Ask for the active dimensions, cabinet or module grid, pitch and native canvas on the same drawing. Have the supplier identify the support frame, trim, power distribution, processor, player and spares included in the offer. Ask the installer to identify site work, access equipment, cable routes and any work that must happen after closing.

For glass, include a sample test against the actual background. For a curved or multi-surface show, assign responsibility for the content template, seam tests and operator training. With those items visible, the exhibit team can compare two offers against the same installation and handover scope.

FAQ
Which fine-pitch LED screen fits a walk-around digital aquarium?
Compare COB Pro and COB Beta layouts for both the long sides and the short ends at the same height. Choose the grid that fits the four active faces and ask for an outside-corner sample. For a walk-in room, point the screens inward and specify an inside corner. Test the smallest species label at the closest visitor position before selecting pixel pitch.
How large does my aquarium LED wall need to be for native 4K?
With COB Pro P0.9375, six cabinets across and six high give 3840 × 2160 pixels on a 3.60 × 2.025 m active face. At P1.25, eight across and eight high give the same native resolution on a 4.80 × 2.70 m face. Add the clearances for trim, the support frame and service access when sizing the architectural opening.
Will visitors see the difference between P0.9375, P1.25 and P1.875?
A 60 mm line contains 64 pixel positions at P0.9375, 48 at P1.25 and 32 at P1.875. The extra samples can preserve a fish’s eye or a thin letter stroke. How much of that detail a visitor notices depends on the content and viewing position. Try the smallest label and a moving clip at the nearest stopping point under operating light.
What measurements do you need for a curved LED wall?
Send a plan showing the display height, the arc length along its face and the direction of the curve. If the radius is unknown, measure the straight line between the ends and the rise from its midpoint to the curve. Mark the closest visitor position, cable entry and maintenance side. The chosen module layout then determines the flat video canvas.
Can LED Film or Holographic LED go on existing aquarium glass?
Start by identifying the dry installation side, glazing material, coating, available edges and exposure to light and cleaning. Test a sample against the real view to assess visibility and reflections. For a water-retaining glass or acrylic window, ask the venue, window supplier and integrator to confirm compatibility, access and the proposed mounting method before specifying an adhesive display.
Can a fish swim around all four sides of a rectangular LED aquarium?
Yes. Treat the faces as one continuous picture: number them clockwise, give each its native pixel width and match the last edge to the first. The integrator can map a panorama or split it into synchronized outputs. For daily changes, staff use that saved layout and the agreed export template. Test all four joins with a moving fish before opening.
Can people watch a digital aquarium from both sides?
An empty tank viewed from two rooms can house two outward-facing displays if the enclosure has enough depth, ventilation and service access. Each side can then receive content oriented for its audience, subject to the playback design. A transparent overlay preserves a view through the surface. Check moving imagery and lettering from both sides before deciding which effect the exhibit needs.
How do you protect the display near water and reach it for maintenance?
Record where condensation forms, which side cleaning spray reaches and whether salt is present. Have the supplier check each exposed face, connection and enclosure against those conditions. On the section drawing, reserve a path to isolate power, remove a module and reach the receiving card or power supply. Check that path again with the finished trim in place.
Can our staff change the video without an LED technician?
For a commissioned single-screen loop, trained staff can normally load a file into the designated player, preview it and activate the playlist using the agreed export template. Keep a working playlist available for rollback. Ask for a hands-on handover using the installed player. New screen layouts, synchronized surfaces or changes to external show cues may also need the integrator.
What should we send to get a project estimate?
For a rectangular island, send its length, depth and display height, the closest visitor position, and a sketch of the walking route. Mark which faces show video, where power enters and how staff will reach the equipment. For an inward-facing exhibit, mark the entrance and inside corners. For glass, say what visitors should still see through the window.

Discuss your brightness requirements

Tell us what the screen needs to do. We can suggest a Square configuration and confirm the brightness and power details for your quote.

Request a Quote
Continue Reading

Leave a Comment

Bring us the brief

Start your project.

A drawing, a site photo or an early idea. Tell us what you are planning and work through the details with our engineering team.

We use these details to respond to your project. Privacy notice.